When creating snapshot with the dataplane enabled, the snapshot file gets
not the actual state of virtqueue, because the current state is stored in
VirtIOBlockDataPlane. Therefore, before saving snapshot need to sync
the dataplane vring state to the virtqueue. The dataplane will resume its
work at the next notify virtqueue.
When snapshot loads with loadvm we get a message:
VQ 0 size 0x80 Guest index 0x15f5 inconsistent with Host index 0x0:
delta 0x15f5
error while loading state for instance 0x0 of device
'0000:00:08.0/virtio-blk'
Error -1 while loading VM state
to reproduce the error I used the following hmp commands:
savevm snap1
loadvm snap1
qemu parameters:
--enable-kvm -smp 4 -m 1024 -drive file=/var/lib/libvirt/images/centos6.4.qcow2,if=none,id=drive-virtio-disk0,format=qcow2,cache=none,aio=native -device virtio-blk-pci,scsi=off,bus=pci.0,addr=0x8,drive=drive-virtio-disk0,id=virtio-disk0 -set device.virtio-disk0.x-data-plane=on
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Message-id: 1445859777-2982-1-git-send-email-den@openvz.org
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 10a06fd65f)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Despite L32E and S32E primary use is for window underflow and overflow
exception handlers they are just normal instructions, and thus need to
check for window overflow.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
(cherry picked from commit f822b7e497)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
commit 5be7d9f1b1
vhost-net: tell tap backend about the vnet endianness
makes vhost net always try to set LE - even if that matches the
native endian-ness.
This makes it fail on older kernels on x86 without TUNSETVNETLE support.
To fix, make qemu_set_vnet_le/qemu_set_vnet_be skip the
ioctl if it matches the host endian-ness.
Reported-by: Marcel Apfelbaum <marcel@redhat.com>
Cc: Greg Kurz <gkurz@linux.vnet.ibm.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
(cherry picked from commit 052bd52fa9)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The test doesn't check that the output makes any sense, only that QEMU
survives. Useful since we've had an astounding number of crash bugs
around there.
In fact, we have a bunch of them right now: a few devices crash or
hang, and some leave dangling pointers behind. The test skips testing
the broken parts. The next commits will fix them up, and drop the
skipping.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1443689999-12182-8-git-send-email-armbru@redhat.com>
(cherry picked from commit 2d1abb850f)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
New convenience function hmp() to facilitate use of
human-monitor-command in tests. Use it to simplify its existing uses.
To blend into existing libqtest code, also add qtest_hmpv() and
qtest_hmp(). That, and the egregiously verbose GTK-Doc comment format
make this patch look bigger than it is.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1443689999-12182-7-git-send-email-armbru@redhat.com>
(cherry picked from commit 5fb48d9673)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
We want to run qom-test for every architecture, without having to
manually add it to every architecture's list of tests. Commit 3687d53
accomplished this by adding it to every architecture's list
automatically.
However, some architectures inherit their tests from others, like this:
check-qtest-x86_64-y = $(check-qtest-i386-y)
check-qtest-microblazeel-y = $(check-qtest-microblaze-y)
check-qtest-xtensaeb-y = $(check-qtest-xtensa-y)
For such architectures, we ended up running the (slow!) test twice.
Commit 2b8419c attempted to avoid this by adding the test only when
it's not already present. Works only as long as we consider adding
the test to the architectures on the left hand side *after* the ones
on the right hand side: x86_64 after i386, microblazeel after
microblaze, xtensaeb after xtensa.
Turns out we consider them in $(SYSEMU_TARGET_LIST) order. Defined as
SYSEMU_TARGET_LIST := $(subst -softmmu.mak,,$(notdir \
$(wildcard $(SRC_PATH)/default-configs/*-softmmu.mak)))
On my machine, this results in the oder xtensa, x86_64, microblazeel,
microblaze, i386. Consequently, qom-test runs twice for microblazeel
and x86_64.
Replace this complex and flawed machinery with a much simpler one: add
generic tests (currently just qom-test) to check-qtest-generic-y
instead of check-qtest-$(target)-y for every target, then run
$(check-qtest-generic-y) for every target.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-Id: <1443689999-12182-5-git-send-email-armbru@redhat.com>
(cherry picked from commit e253c28715)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This causes the region to outlive the object, because it attaches the
region to /machine. This is not nice for the "realize" method, but
much worse for "instance_init" because it can cause dangling pointers
after a simple object_new/object_unref pair.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1443689999-12182-3-git-send-email-armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 81e0ab48dd)
Conflicts:
hw/display/cg3.c
hw/display/tcx.c
* removed context dependencies on &error_fatal/&error_abort
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This is legal; the MemoryRegion will simply unreference all the
existing subregions and possibly bring them down with it as well.
However, it requires a bit of care to avoid an infinite loop.
Finalizing a memory region cannot trigger an address space update,
but memory_region_del_subregion errs on the side of caution and
might trigger a spurious update: avoid that by resetting mr->enabled
first.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1443689999-12182-2-git-send-email-armbru@redhat.com>
(cherry picked from commit 2e2b8eb70f)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The next commit will compile hw/input/virtio-input.c and
hw/input/virtio-input-hid.c even when CONFIG_LINUX is off. These
files include both "include/standard-headers/linux/input.h" and
<windows.h> then. Doesn't work, because both define SW_MAX. We don't
actually use it. Patch input.h to define SW_MAX_ instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1444320700-26260-2-git-send-email-armbru@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
(cherry picked from commit ac98fa849e)
Conflicts:
scripts/update-linux-headers.sh
* remove dependency on eddb4de3
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The malloc vtable is not supported anymore in glib, because it broke
when constructors called g_malloc. Remove tracing of g_malloc,
g_realloc and g_free calls.
Note that, for systemtap users, glib also provides tracepoints
glib.mem_alloc, glib.mem_free, glib.mem_realloc, glib.slice_alloc
and glib.slice_free.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 1442417924-25831-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 98cf48f60a)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
When packet is truncated during receiving, we drop the packets but
neither discard the descriptor nor add and signal used
descriptor. This will lead several issues:
- sg mappings are leaked
- rx will be stalled if a lots of packets were truncated
In order to be consistent with vhost, fix by discarding the descriptor
in this case.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 0cf33fb6b4)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This patch introduces virtqueue_discard() to discard a descriptor and
unmap the sgs. This will be used by the patch that will discard
descriptor when packet is truncated.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 29b9f5efd7)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Device hotplugs trigger a crw machine check. All machine checks
have validity bits for certain register types. With vector support
we also have to claim that vector registers are valid.
This is a band-aid suitable for stable. Long term we should
create the full mcic value dynamically depending on the active
features in the kernel interrupt handler.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
(cherry picked from commit 2ab75df38e)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This reverts commit 31bed5509d.
The reverted commit changed qdev_device_help() to reject abstract
devices and devices that have cannot_instantiate_with_device_add_yet
set, to fix crash bugs like -device x86_64-cpu,help.
Rejecting abstract devices makes sense: they're purely internal, and
the implementation of the help feature can't cope with them.
Rejecting non-pluggable devices makes less sense: even though you
can't use them with -device, the help may still be useful elsewhere,
for instance with -global. This is a regression: -device FOO,help
used to help even for FOO that aren't pluggable.
The previous two commits fixed the crash bug at a lower layer, so
reverting this one is now safe. Fixes the -device FOO,help
regression, except for the broken devices marked
cannot_even_create_with_object_new_yet. For those, the error message
is improved.
Example of a device where the regression is fixed:
$ qemu-system-x86_64 -device PIIX4_PM,help
PIIX4_PM.command_serr_enable=bool (on/off)
PIIX4_PM.multifunction=bool (on/off)
PIIX4_PM.rombar=uint32
PIIX4_PM.romfile=str
PIIX4_PM.addr=int32 (Slot and optional function number, example: 06.0 or 06)
PIIX4_PM.memory-hotplug-support=bool
PIIX4_PM.acpi-pci-hotplug-with-bridge-support=bool
PIIX4_PM.s4_val=uint8
PIIX4_PM.disable_s4=uint8
PIIX4_PM.disable_s3=uint8
PIIX4_PM.smb_io_base=uint32
Example of a device where it isn't fixed:
$ qemu-system-x86_64 -device host-x86_64-cpu,help
Can't list properties of device 'host-x86_64-cpu'
Both failed with "Parameter 'driver' expects pluggable device type"
before.
Cc: qemu-stable@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1443689999-12182-11-git-send-email-armbru@redhat.com>
(cherry picked from commit 33fe968330)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Several devices don't survive object_unref(object_new(T)): they crash
or hang during cleanup, or they leave dangling pointers behind.
This breaks at least device-list-properties, because
qmp_device_list_properties() needs to create a device to find its
properties. Broken in commit f4eb32b "qmp: show QOM properties in
device-list-properties", v2.1. Example reproducer:
$ qemu-system-aarch64 -nodefaults -display none -machine none -S -qmp stdio
{"QMP": {"version": {"qemu": {"micro": 50, "minor": 4, "major": 2}, "package": ""}, "capabilities": []}}
{ "execute": "qmp_capabilities" }
{"return": {}}
{ "execute": "device-list-properties", "arguments": { "typename": "pxa2xx-pcmcia" } }
qemu-system-aarch64: /home/armbru/work/qemu/memory.c:1307: memory_region_finalize: Assertion `((&mr->subregions)->tqh_first == ((void *)0))' failed.
Aborted (core dumped)
[Exit 134 (SIGABRT)]
Unfortunately, I can't fix the problems in these devices right now.
Instead, add DeviceClass member cannot_destroy_with_object_finalize_yet
to mark them:
* Hang during cleanup (didn't debug, so I can't say why):
"realview_pci", "versatile_pci".
* Dangling pointer in cpus: most CPUs, plus "allwinner-a10", "digic",
"fsl,imx25", "fsl,imx31", "xlnx,zynqmp", because they create such
CPUs
* Assert kvm_enabled(): "host-x86_64-cpu", host-i386-cpu",
"host-powerpc64-cpu", "host-embedded-powerpc-cpu",
"host-powerpc-cpu" (the powerpc ones can't currently reach the
assertion, because the CPUs are only registered when KVM is enabled,
but the assertion is arguably in the wrong place all the same)
Make qmp_device_list_properties() fail cleanly when the device is so
marked. This improves device-list-properties from "crashes, hangs or
leaves dangling pointers behind" to "fails". Not a complete fix, just
a better-than-nothing work-around. In the above reproducer,
device-list-properties now fails with "Can't list properties of device
'pxa2xx-pcmcia'".
This also protects -device FOO,help, which uses the same machinery
since commit ef52358 "qdev-monitor: include QOM properties in -device
FOO, help output", v2.2. Example reproducer:
$ qemu-system-aarch64 -machine none -device pxa2xx-pcmcia,help
Before:
qemu-system-aarch64: .../memory.c:1307: memory_region_finalize: Assertion `((&mr->subregions)->tqh_first == ((void *)0))' failed.
After:
Can't list properties of device 'pxa2xx-pcmcia'
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Anthony Green <green@moxielogic.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Jia Liu <proljc@gmail.com>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: qemu-ppc@nongnu.org
Cc: qemu-stable@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1443689999-12182-10-git-send-email-armbru@redhat.com>
(cherry picked from commit 4c315c2766)
Conflicts:
hw/arm/fsl-imx25.c
hw/arm/fsl-imx31.c
target-tilegx/cpu.c
tests/device-introspect-test.c
* removed hunks pertaining to devices/tests not in 2.4
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Commit 6e99c63 ("net/socket: Drop net_socket_can_send") changed the
semantics around .can_receive for sockets to now require the device to
flush queued pkts when transitioning to a .can_receive=true state. But
it's OK to drop incoming packets when the link is not active.
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 2734a20b81)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
After commit 019a3edbb2 ("virtio: make
features 64bit wide"). Device's guest_features was actually set after
vdc->load(). This breaks the assumption that device specific load()
function can check guest_features. For virtio-net, self announcement
and guest offloads won't work after migration.
Fixing this by defer them to virtio_net_load() where guest_features
were guaranteed to be set. Other virtio devices looks fine.
Fixes: 019a3edbb2
("virtio: make features 64bit wide")
Cc: qemu-stable@nongnu.org
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
(cherry picked from commit 1f8828ef57)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Commit ef546f1275 ("virtio: add
feature checking helpers") introduced a helper __virtio_has_feature.
We don't want to use reserved identifiers, though, so let's
rename __virtio_has_feature to virtio_has_feature and virtio_has_feature
to virtio_vdev_has_feature.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit 95129d6fc9)
* prereq for 1f8828e
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The xscmpodp and xscmpudp instructions only have the AX, BX bits in
there encoding, the lowest bit (usually TX) is marked as an invalid
bit. We therefore can't decode them with GEN_XX2FORM, which decodes
the two lowest bit.
Introduce a new form GEN_XX2FORM, which decodes AX and BX and mark
the lowest bit as invalid.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
(cherry picked from commit 8f60f8e2e5)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
For vector instructions, the helpers get pointers to the vector register
in arguments. Some operands might point to the same register, including
the operand holding the result.
When emulating instructions which access the vector elements in a
non-linear way, we need to store the result in an temporary variable.
This fixes openssl when emulating a POWER8 CPU.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
(cherry picked from commit 65cf1f65be)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The MIPS TCG backend implements qemu_ld with 64-bit targets using the v0
register (base) as a temporary to load the upper half of the QEMU TLB
comparator (see line 5 below), however this happens before the input
address is used (line 8 to mask off the low bits for the TLB
comparison, and line 12 to add the host-guest offset). If the input
address (addrl) also happens to have been placed in v0 (as in the second
column below), it gets clobbered before it is used.
addrl in t2 addrl in v0
1 srl a0,t2,0x7 srl a0,v0,0x7
2 andi a0,a0,0x1fe0 andi a0,a0,0x1fe0
3 addu a0,a0,s0 addu a0,a0,s0
4 lw at,9136(a0) lw at,9136(a0) set TCG_TMP0 (at)
5 lw v0,9140(a0) lw v0,9140(a0) set base (v0)
6 li t9,-4093 li t9,-4093
7 lw a0,9160(a0) lw a0,9160(a0) set addend (a0)
8 and t9,t9,t2 and t9,t9,v0 use addrl
9 bne at,t9,0x836d8c8 bne at,t9,0x836d838 use TCG_TMP0
10 nop nop
11 bne v0,t8,0x836d8c8 bne v0,a1,0x836d838 use base
12 addu v0,a0,t2 addu v0,a0,v0 use addrl, addend
13 lw t0,0(v0) lw t0,0(v0)
Fix by using TCG_TMP0 (at) as the temporary instead of v0 (base),
pushing the load on line 5 forward into the delay slot of the low
comparison (line 10). The early load of the addend on line 7 also needs
pushing even further for 64-bit targets, or it will clobber a0 before
we're done with it. The output for 32-bit targets is unaffected.
srl a0,v0,0x7
andi a0,a0,0x1fe0
addu a0,a0,s0
lw at,9136(a0)
-lw v0,9140(a0) load high comparator
li t9,-4093
-lw a0,9160(a0) load addend
and t9,t9,v0
bne at,t9,0x836d838
- nop
+ lw at,9140(a0) load high comparator
+lw a0,9160(a0) load addend
-bne v0,a1,0x836d838
+bne at,a1,0x836d838
addu v0,a0,v0
lw t0,0(v0)
Cc: qemu-stable@nongnu.org
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
(cherry picked from commit 5eb4f645eb)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
When a function returns a null pointer on error and only on error, you
can do
if (!foo(foos, errp)) {
... handle error ...
}
instead of the more cumbersome
Error *err = NULL;
if (!foo(foos, &err)) {
error_propagate(errp, err);
... handle error ...
}
A StringProperty's getter, however, may return null on success! We
then fail to call visit_type_str().
Screwed up in 6a146eb, v1.1.
Fails tests/qom-test in my current, heavily hacked QAPI branch. No
reproducer for master known (but I didn't look hard).
Cc: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Andreas Färber <afaerber@suse.de>
(cherry picked from commit e1c8237df5)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The argument for an Error **errp parameter must point to a null
pointer. If it doesn't, and an error happens, error_set() fails its
assertion.
Instead of
foo(foos, errp);
bar(bars, errp);
you need to do something like
Error *err = NULL;
foo(foos, &err);
if (err) {
error_propagate(errp, err);
goto out;
}
bar(bars, errp);
out:
Screwed up in commit 0e55884 (v1.3.0): property_get_bool().
Screwed up in commit 1f21772 (v2.1.0): object_property_get_enum() and
object_property_get_uint16List().
Screwed up in commit a8e3fbe (v2.4.0): property_get_enum(),
property_set_enum().
Found by inspection, no actual crashes observed.
Fix them up.
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: Hu Tao <hutao@cn.fujitsu.com>
Cc: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Andreas Färber <afaerber@suse.de>
(cherry picked from commit 4715d42efe)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
IDEState's io_buffer_offset was originally added to keep track of offsets
in AHCI rather exclusively, but it was added to IDEState instead of an
AHCI-specific structure.
AHCI fakes all PIO transfers using DMA and a scatter-gather list. When
the core or atapi layers invoke HBA-specific mechanisms for transfers,
they do not always know that it is being backed by DMA or a sglist, so
this offset is not always updated by the HBA code everywhere.
If we modify it in dma_buf_commit, however, any HBA that needs to use
this offset to manage operating on only part of a sglist will have
access to it.
This will fix ATAPI PIO transfers performed through the AHCI HBA,
which were previously not modifying this value appropriately.
This will fix ATAPI PIO transfers larger than one sector.
Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1440546331-29087-2-git-send-email-jsnow@redhat.com
CC: qemu-stable@nongnu.org
(cherry picked from commit aaeda4a3c9)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
PAPR requires ibm,req#msi and ibm,req#msi-x to be present in the
device node to define the number of msi/msi-x interrupts the device
supports, respectively.
Currently we have ibm,req#msi-x hardcoded to a non-sensical constant
that happens to be 2, and are missing ibm,req#msi entirely. The result
of that is that msi-x capable devices get limited to 2 msi-x
interrupts (which can impact performance), and msi-only devices likely
wouldn't work at all. Additionally, if devices expect a minimum that
exceeds 2, the guest driver may fail to load entirely.
SLOF still owns the generation of these properties at boot-time
(although other device properties have since been offloaded to QEMU),
but for hotplugged devices we rely on the values generated by QEMU
and thus hit the limitations above.
Fix this by generating these properties in QEMU as expected by guests.
In the future it may make sense to modify SLOF to pass through these
values directly as we do with other props since we're duplicating SLOF
code.
Cc: qemu-ppc@nongnu.org
Cc: qemu-stable@nongnu.org
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
(cherry picked from commit a8ad731a00)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The QEMU code is not internationalized and assumes that it runs under
the C locale, but if we use the GTK+ UI we'll end up importing the
locale settings from the environment. This can break things, such as
the JSON generator and iotest 120 in locales that use a decimal comma.
We do however have translations for a few simple strings for the GTK+
menu items, so in order to run QEMU using the C locale, and yet have a
translated UI let's use setlocale() for LC_MESSAGES only.
Cc: qemu-stable@nongnu.org
Signed-off-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
(cherry picked from commit 2cb5d2a47c)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
We're a little too lenient with what we'll let an ATAPI drive handle.
Clamp down on the IDE command execution table to remove CD_OK permissions
from commands that are not and have never been ATAPI commands.
For ATAPI command validity, please see:
- ATA4 Section 6.5 ("PACKET Command feature set")
- ATA8/ACS Section 4.3 ("The PACKET feature set")
- ACS3 Section 4.3 ("The PACKET feature set")
ACS3 has a historical command validity table in Table B.4
("Historical Command Assignments") that can be referenced to find when
a command was introduced, deprecated, obsoleted, etc.
The only reference for ATAPI command validity is by checking that
version's PACKET feature set section.
ATAPI was introduced by T13 into ATA4, all commands retired prior to ATA4
therefore are assumed to have never been ATAPI commands.
Mandatory commands, as listed in ATA8-ACS3, are:
- DEVICE RESET
- EXECUTE DEVICE DIAGNOSTIC
- IDENTIFY DEVICE
- IDENTIFY PACKET DEVICE
- NOP
- PACKET
- READ SECTOR(S)
- SET FEATURES
Optional commands as listed in ATA8-ACS3, are:
- FLUSH CACHE
- READ LOG DMA EXT
- READ LOG EXT
- WRITE LOG DMA EXT
- WRITE LOG EXT
All other commands are illegal to send to an ATAPI device and should
be rejected by the device.
CD_OK removal justifications:
0x06 WIN_DSM Defined in ACS2. Not valid for ATAPI.
0x21 WIN_READ_ONCE Retired in ATA5. Not ATAPI in ATA4.
0x94 WIN_STANDBYNOW2 Retired in ATA4. Did not coexist with ATAPI.
0x95 WIN_IDLEIMMEDIATE2 Retired in ATA4. Did not coexist with ATAPI.
0x96 WIN_STANDBY2 Retired in ATA4. Did not coexist with ATAPI.
0x97 WIN_SETIDLE2 Retired in ATA4. Did not coexist with ATAPI.
0x98 WIN_CHECKPOWERMODE2 Retired in ATA4. Did not coexist with ATAPI.
0x99 WIN_SLEEPNOW2 Retired in ATA4. Did not coexist with ATAPI.
0xE0 WIN_STANDBYNOW1 Not part of ATAPI in ATA4, ACS or ACS3.
0xE1 WIN_IDLEIMMDIATE Not part of ATAPI in ATA4, ACS or ACS3.
0xE2 WIN_STANDBY Not part of ATAPI in ATA4, ACS or ACS3.
0xE3 WIN_SETIDLE1 Not part of ATAPI in ATA4, ACS or ACS3.
0xE4 WIN_CHECKPOWERMODE1 Not part of ATAPI in ATA4, ACS or ACS3.
0xE5 WIN_SLEEPNOW1 Not part of ATAPI in ATA4, ACS or ACS3.
0xF8 WIN_READ_NATIVE_MAX Obsoleted in ACS3. Not ATAPI in ATA4 or ACS.
This patch fixes a divide by zero fault that can be caused by sending
the WIN_READ_NATIVE_MAX command to an ATAPI drive, which causes it to
attempt to use zeroed CHS values to perform sector arithmetic.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1441816082-21031-1-git-send-email-jsnow@redhat.com
CC: qemu-stable@nongnu.org
(cherry picked from commit d9033e1d3a)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Sadly, some images may have more clusters than what can be represented
using a plain int. We should be prepared for that case (in
qcow2_check_refcounts() we actually were trying to catch that case, but
since size_to_clusters() truncated the returned value, that check never
did anything useful).
Cc: qemu-stable <qemu-stable@nongnu.org>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit b6d36def6d)
Conflicts:
block/qcow2-cluster.c
block/qcow2.h
* removed context dependency on ff99129a
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This is a bug fix for aarch64. At present, we have branches using
the 32-bit (translate.c) versions of cpu_[NZCV]F, but we set the flags
using the 64-bit (translate-a64.c) versions of cpu_[NZCV]F. From
the view of the TCG code generator, these are unrelated variables.
The bug is hard to see because we currently only read these variables
from branches, and upon reaching a branch TCG will first spill live
variables and then reload the arguments of the branch. Since the
32-bit versions were never live until reaching the branch, we'd re-read
the data that had just been spilled from the 64-bit versions.
There is currently no such problem with the cpu_exclusive_* variables,
but there's no point in tempting fate.
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-id: 1441909103-24666-2-git-send-email-rth@twiddle.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 78bcaa3e37)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
When operation in standard mode, we currently return the size
of packet during buffer overflow. This consumes the overflow
packet. Return 0 instead so we can re-process the overflow packet
when we have room.
This fixes issues with lost/dropped fragments of large messages.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1441121206-6997-3-git-send-email-vyasevic@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 26c4e7ca72)
*removed dependency on b76f21a7
*removed context dependency on 4cbea598
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
rtl8139_do_receive() tries to check for the overflow condition
by making sure that packet_size + 8 does not exceed the
available buffer space. The issue here is that RxBuffAddr,
used to calculate available buffer space, is aligned to a
a 4 byte boundry after every update. So it is possible that
every packet ends up being slightly padded when written
to the receive buffer. This padding is not taken into
account when checking for overflow and we may end up missing
the overflow condition can causing buffer overwrite.
This patch takes alignment into consideration when
checking for overflow condition.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1441121206-6997-2-git-send-email-vyasevic@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit fabdcd3392)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
When executing the start function, we should start with a clear state
regarding subchannel and device status; it is easy to forget updating one
of them after the ccw has been processed.
Note that we don't need to care about resetting the various control
fields: They are cleared by tsch(), and if they were still pending,
we wouldn't be able to execute the start function in the first
place.
Also note that we don't want to clear cstat/dstat if a suspended
subchannel is resumed.
This fixes a bug where we would continue to present channel-program
check in cstat even though later ccw requests for the subchannel
finished without error (i.e. cstat should be 0).
Cc: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
(cherry picked from commit 6b7741c2be)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The current U-Boot binary in QEMU has a bug where it fails to support
dynamic CCSR addressing. Without this support, u-boot can not boot the
ppce500 machine anymore. This has been fixed upstream in u-boot commit
e834975b.
Update the u-boot blob we carry in QEMU to the latest u-boot upstream,
so that we can successfully run u-boot with the ppce500 machine again.
CC: qemu-stable@nongnu.org
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit d4574435a6)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The code to flush the DBDMA channel was effectively duplicated in
dbdma_control_write(), except for the fact that the copy executed outside of a
RUN bit transition was broken by not clearing the FLUSH bit once the flush was
complete.
Newer PPC Linux kernels would timeout waiting for the FLUSH bit to clear again
after submitting a FLUSH command. Fix this by always clearing the FLUSH bit
once the channel flush is complete and removing the repeated code.
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
(cherry picked from commit 1cde732d88)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Example:
$ ./qemu-img create -f qcow2 /tmp/t.qcow2 64M
$ ./qemu-img amend -f qcow2 -o backing_file=/tmp/t.qcow2, -o help \
/tmp/t.qcow2
This should not crash. This actually is tested by iotest 082, but not
caught due to the segmentation fault being silent (which is something
that needs to be fixed, too).
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: qemu-stable <qemu-stable@nongnu.org>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit e814dffcc9)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This subtraction of return addresses applies directly to TCI as well as
host-TCG. This fixes Linux boots for at least Microblaze, CRIS, ARM and
SH4 when using TCI.
[sw: Removed indentation for preprocessor statement]
[sw: The patch also fixes Linux boot for x86_64]
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
(cherry picked from commit a17d448274)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
A spurious trailing "\n" in the gdb syscall format string used
for SYS_WRITE0 meant that gdb would reject the remote syscall,
with the effect that the output from the guest was silently dropped.
Remove the newline so that gdb accepts the packet.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 857b55adb7)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
This fixes a regression introduced by commit dcfb3beb ("mirror: Do zero
write on target if sectors not allocated"), which was reported to cause
aborts with the message "Co-routine re-entered recursively".
The cause for this bug is the following code in mirror_iteration_done():
if (s->common.busy) {
qemu_coroutine_enter(s->common.co, NULL);
}
This has always been ugly because - unlike most places that reenter - it
doesn't have a specific yield that it pairs with, but is more
uncontrolled. What we really mean here is "reenter the coroutine if
it's in one of the four explicit yields in mirror.c".
This used to be equivalent with s->common.busy because neither
mirror_run() nor mirror_iteration() call any function that could yield.
However since commit dcfb3beb this doesn't hold true any more:
bdrv_get_block_status_above() can yield.
So what happens is that bdrv_get_block_status_above() wants to take a
lock that is already held, so it adds itself to the queue of waiting
coroutines and yields. Instead of being woken up by the unlock function,
however, it gets woken up by mirror_iteration_done(), which is obviously
wrong.
In most cases the code actually happens to cope fairly well with such
cases, but in this specific case, the unlock must already have scheduled
the coroutine for wakeup when mirror_iteration_done() reentered it. And
then the coroutine happened to process the scheduled restarts and tried
to reenter itself recursively.
This patch fixes the problem by pairing the reenter in
mirror_iteration_done() with specific yields instead of abusing
s->common.busy.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Message-id: 1439455310-11263-1-git-send-email-kwolf@redhat.com
Signed-off-by: Jeff Cody <jcody@redhat.com>
(cherry picked from commit e424aff5f3)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The last portion of an unaligned WRITE SAME command could fail the
assertion in bdrv_aligned_pwritev:
assert(!qiov || bytes == qiov->size);
Because we updated data->iov.iov_len right above this if block, but
data->qiov still has the old size.
Reinitialize the qiov to make them equal and keep block layer happy.
Cc: qemu-stable@nongnu.org
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <1438159512-3871-2-git-send-email-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
(cherry picked from commit a56537a127)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Ne2000 NIC uses ring buffer of NE2000_MEM_SIZE(49152)
bytes to process network packets. While receiving packets
via ne2000_receive() routine, a local 'index' variable
could exceed the ring buffer size, leading to an infinite
loop situation.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: P J P <pjp@fedoraproject.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 737d2b3c41)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Ne2000 NIC uses ring buffer of NE2000_MEM_SIZE(49152)
bytes to process network packets. While receiving packets
via ne2000_receive() routine, a local 'index' variable
could exceed the ring buffer size, which could lead to a
memory buffer overflow. Added other checks at initialisation.
Reported-by: Qinghao Tang <luodalongde@gmail.com>
Signed-off-by: P J P <pjp@fedoraproject.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
(cherry picked from commit 9bbdbc66e5)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The _cmp_bytes variable added by commit "bea60dd ui/vnc: fix potential
memory corruption issues" can become negative. Result is (possibly
exploitable) memory corruption. Reason for that is it uses the stride
instead of bytes per scanline to apply limits.
For the server surface is is actually fine. vnc creates that itself,
there is never any padding and thus scanline length always equals stride.
For the guest surface scanline length and stride are typically identical
too, but it doesn't has to be that way. So add and use a new variable
(guest_ll) for the guest scanline length. Also rename min_stride to
line_bytes to make more clear what it actually is. Finally sprinkle
in an assert() to make sure we never use a negative _cmp_bytes again.
Reported-by: 范祚至(库特) <zuozhi.fzz@alibaba-inc.com>
Reviewed-by: P J P <ppandit@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
(cherry picked from commit eb8934b041)
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
virtio fix for 2.4
Fixes migration in virtio 1 mode.
We still have a known bug with memory hotplug, it doesn't
look like we can fix that in time for 2.4.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 05 Aug 2015 15:57:39 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
virtio: fix 1.0 virtqueue migration
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 488981a4 [block: convert quorum blockdrv to use crypto APIs]
broke qemu-iotest 041 on hosts with GnuTLS < 2.10.0. It converted a
compile-time check to a run-time check at device open time. The result
is that we now advertise a feature (the quorum block driver) that will
never work (on those hosts). There's no way (short of parsing
human-readable error messages) for qemu-iotests or any other API
consumer to recognise that the quorum block driver isn't _actually_
available and shouldn't be used or tested.
Move the run-time check to bdrv_quorum_init() to avoid registering the
quorum block driver if we know it cannot work. This way API consumers
can recognise it's unavailable.
Fixes: 488981a4af
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 1438699705-21761-1-git-send-email-silbe@linux.vnet.ibm.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
1.0 does not requires physically-contiguous pages layout for a
virtqueue. So we could not infer avail and used from desc. This means
we need to migrate vring.avail and vring.used when host support virtio
1.0. This fixes malfunction of virtio 1.0 device after migration.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
X86 queue, 2015-08-04
# gpg: Signature made Tue 04 Aug 2015 16:49:42 BST using RSA key ID 984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-pull-request:
target-i386: fix IvyBridge xlevel in PC_COMPAT_2_3
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MIPS patches 2015-08-04
Changes:
* fix semihosting for microMIPS R6
* fix an abort when booting mips64 kernel with --enable-tcg-debug
# gpg: Signature made Tue 04 Aug 2015 12:32:17 BST using RSA key ID 0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4 4FC0 5211 8E3C 0B29 DA6B
* remotes/lalrae/tags/mips-20150804:
target-mips: Copy restrictions from ext/ins to dext/dins
target-mips: fix semihosting for microMIPS R6
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The checks in dins is required to avoid triggering an assertion
in tcg_gen_deposit_tl. The check in dext is just for completeness.
Fold the other D cases in via fallthru.
In this case the errant dins appears to be data, not code, as
translation failed to stop after a break insn.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
In semihosting mode the SDBBP 1 instructions should trigger UHI syscall,
but in QEMU this does not happen for recently added microMIPS R6.
Consequently bare metal microMIPS R6 programs supporting UHI will not run.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
cve-2015-5166
# gpg: Signature made Mon 03 Aug 2015 15:27:44 BST using RSA key ID 70E1AE90
# gpg: Good signature from "Stefano Stabellini <stefano.stabellini@eu.citrix.com>"
* remotes/sstabellini/tags/cve-2015-5166-tag:
Fix release_drive on unplugged devices (pci_piix3_xen_ide_unplug)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
xen-migration-2.4
# gpg: Signature made Mon 03 Aug 2015 17:18:36 BST using RSA key ID 70E1AE90
# gpg: Good signature from "Stefano Stabellini <stefano.stabellini@eu.citrix.com>"
* remotes/sstabellini/tags/xen-migration-2.4-tag:
migration: Fix regression for xenfv and pc,accel=xen machine.
migration: Fix global state with Xen.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fix migration from the same QEMU version and from previous QEMU
version.
>From the global state section, we don't need runstate with Xen. Right now,
the way the Xen toolstack knows when QEMU is ready is when QEMU reach
"running" runstate.
The configuration section and the section footers are not going to be
present in previous version of QEMU with xenfv machine, so we skip them.
The Xen toolstack libxenlight does not specify a particular version of the
'pc' machine, so migration from older version of QEMU used by Xen to newer
one would break due to missing "configuration" section and section footers.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
When doing migration via the QMP command xen_save_devices_state, the
current runstate is not store into the global state section. Also the
current runstate is not the one we want on the receiver side.
During migration, the Xen toolstack paused QEMU before save the devices
state. Also, the toolstack expect QEMU to autostart when the migration is
finished.
So this patch store "running" as it's current runstate.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
pci_piix3_xen_ide_unplug should completely unhook the unplugged
IDEDevice from the corresponding BlockBackend, otherwise the next call
to release_drive will try to detach the drive again.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Pull request
# gpg: Signature made Mon Aug 3 13:08:25 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/rtl8139-cplus-tx-input-validation-pull-request:
rtl8139: check TCP Data Offset field (CVE-2015-5165)
rtl8139: skip offload on short TCP header (CVE-2015-5165)
rtl8139: check IP Total Length field (CVE-2015-5165)
rtl8139: check IP Header Length field (CVE-2015-5165)
rtl8139: skip offload on short Ethernet/IP header (CVE-2015-5165)
rtl8139: drop tautologous if (ip) {...} statement (CVE-2015-5165)
rtl8139: avoid nested ifs in IP header parsing (CVE-2015-5165)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The TCP Data Offset field contains the length of the header. Make sure
it is valid and does not exceed the IP data length.
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
TCP Large Segment Offload accesses the TCP header in the packet. If the
packet is too short we must not attempt to access header fields:
tcp_header *p_tcp_hdr = (tcp_header*)(eth_payload_data + hlen);
int tcp_hlen = TCP_HEADER_DATA_OFFSET(p_tcp_hdr);
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The IP Total Length field includes the IP header and data. Make sure it
is valid and does not exceed the Ethernet payload size.
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Transmit offload features access Ethernet and IP headers the packet. If
the packet is too short we must not attempt to access header fields:
int proto = be16_to_cpu(*(uint16_t *)(saved_buffer + 12));
...
eth_payload_data = saved_buffer + ETH_HLEN;
...
ip = (ip_header*)eth_payload_data;
if (IP_HEADER_VERSION(ip) != IP_HEADER_VERSION_4) {
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The previous patch stopped using the ip pointer as an indicator that the
IP header is present. When we reach the if (ip) {...} statement we know
ip is always non-NULL.
Remove the if statement to reduce nesting.
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Transmit offload needs to parse packet headers. If header fields have
unexpected values the offload processing is skipped.
The code currently uses nested ifs because there is relatively little
input validation. The next patches will add missing input validation
and a goto label is more appropriate to avoid deep if statement nesting.
Reported-by: 朱东海(启路) <donghai.zdh@alibaba-inc.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
TCG MIPS and S390 fixes for 2.4.
# gpg: Signature made Mon Aug 3 09:09:59 2015 BST using RSA key ID 1DDD8C9B
# gpg: Good signature from "Aurelien Jarno <aurelien@aurel32.net>"
# gpg: aka "Aurelien Jarno <aurelien@jarno.fr>"
# gpg: aka "Aurelien Jarno <aurel32@debian.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7746 2642 A9EF 94FD 0F77 196D BA9C 7806 1DDD 8C9B
* remotes/aurel/tags/pull-tcg-mips-s390-20150803:
tcg/mips: fix add2
tcg/s390x: Mask TCGMemOp appropriately for indexing
tcg/mips: Mask TCGMemOp appropriately for indexing
tcg/mips: fix TLB loading for BE host with 32-bit guests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# gpg: Signature made Fri Jul 31 23:24:06 2015 BST using RSA key ID AAFC390E
# gpg: Good signature from "John Snow (John Huston) <jsnow@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: FAEB 9711 A12C F475 812F 18F2 88A9 064D 1835 61EB
# Subkey fingerprint: F9B7 ABDB BCAC DF95 BE76 CBD0 7DEF 8106 AAFC 390E
* remotes/jnsnow/tags/ide-pull-request:
ahci: fix ICC mask definition
macio: re-add TRIM support
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The add2 code in the tcg_out_addsub2 function doesn't take into account
the case where rl == al == bl. In that case we can't compute the carry
after the addition. As it corresponds to a multiplication by 2, the
carry bit is the bit 31.
While this is a corner case, this prevents x86-64 guests to boot on a
MIPS host.
Cc: qemu-stable@nongnu.org
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Commit 2b7ec66f fixed TCGMemOp masking following the MO_AMASK addition,
but two cases were forgotten in the TCG S390 backend.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Commit 2b7ec66f fixed TCGMemOp masking following the MO_AMASK addition,
but two cases were forgotten in the TCG MIPS backend.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For 32-bit guest, we load a 32-bit address from the TLB, so there is no
need to compensate for the low or high part. This fixes 32-bit guests on
big-endian hosts.
Cc: qemu-stable@nongnu.org
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There are likely others that could be updated, but we'll
go with a light touch for 2.4 for now.
Without the Unsigned specifier, this shifts bits into the
signed bit, which makes clang unhappy and could cause
unwanted behavior.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1437501721-24495-1-git-send-email-jsnow@redhat.com
Pull request
These fixes make dataplane work again after the notify_me optimization was
added. They also solve QEMUBH memory leaks and fix a bug in dataplane's
cleanup code.
# gpg: Signature made Wed Jul 29 14:50:26 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/block-pull-request:
AioContext: force event loop iteration using BH
AioContext: avoid leaking BHs on cleanup
virtio-blk-dataplane: delete bottom half before the AioContext is freed
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The notify_me optimization introduced in commit eabc977973
("AioContext: fix broken ctx->dispatching optimization") skips
event_notifier_set() calls when the event loop thread is not blocked in
ppoll(2).
This optimization causes a deadlock if two aio_context_acquire() calls
race. notify_me = 0 during the race so the winning thread can enter
ppoll(2) unaware that the other thread is waiting its turn to acquire
the AioContext.
This patch forces ppoll(2) to return by scheduling a BH instead of
calling aio_notify().
The following deadlock with virtio-blk dataplane is fixed:
qemu ... -object iothread,id=iothread0 \
-drive if=none,id=drive0,file=test.img,... \
-device virtio-blk-pci,iothread=iothread0,drive=drive0
This command-line results in a hang early on without this patch.
Thanks to Paolo Bonzini <pbonzini@redhat.com> for investigating this bug
with me.
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1438101249-25166-4-git-send-email-pbonzini@redhat.com
Message-Id: <1438014819-18125-3-git-send-email-stefanha@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Pull request
These two .can_receive() are now reviewed. The net subsystem queue for 2.4 is now empty.
# gpg: Signature made Tue Jul 28 13:26:03 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/net-pull-request:
xen: Drop net_rx_ok
hw/net: handle flow control in mcf_fec driver receiver
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
virtio fixes for 2.4
Mostly virtio 1 spec compliance fixes.
We are unlikely to make it perfectly compliant in
the first release, but it seems worth it to try.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon Jul 27 21:55:48 2015 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
virtio: minor cleanup
acpi: fix pvpanic device is not shown in ui
virtio-blk: only clear VIRTIO_F_ANY_LAYOUT for legacy device
virtio-blk: fail get_features when both scsi and 1.0 were set
virtio: get_features() can fail
virtio-pci: fix memory MR cleanup for modern
virtio: set any_layout in virtio core
virtio-9p: fix any_layout
virtio-serial: fix ANY_LAYOUT
virtio: hide legacy features from modern guests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MIPS patches 2015-07-28
Changes:
* net/dp8393x fixes
* Vectored Interrupts bug fix
* fix for a bug in machine.c which was provoking a warning on FreeBSD
# gpg: Signature made Tue Jul 28 10:47:19 2015 BST using RSA key ID 0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4 4FC0 5211 8E3C 0B29 DA6B
* remotes/lalrae/tags/mips-20150728:
net/dp8393x: do not use memory_region_init_rom_device with NULL
net/dp8393x: remove check of runt packets
net/dp8393x: disable user creation
target-mips: fix offset calculation for Interrupts
target-mips: fix passing incompatible pointer type in machine.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* crypto fixes
* megasas SIGSEGV fix
* memory refcount change to fix virtio hot-unplug
# gpg: Signature made Tue Jul 28 08:29:07 2015 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
memory: do not add a reference to the owner of aliased regions
megasas: Add write function to handle write access to PCI BAR 3
crypto: extend unit tests to cover decryption too
crypto: fix built-in AES decrypt function
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# gpg: Signature made Tue Jul 28 05:22:29 2015 BST using RSA key ID C0DE3057
# gpg: Good signature from "Jeffrey Cody <jcody@redhat.com>"
# gpg: aka "Jeffrey Cody <jeff@codyprime.org>"
# gpg: aka "Jeffrey Cody <codyprime@gmail.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 9957 4B4D 3474 90E7 9D98 D624 BDBE 7B27 C0DE 3057
* remotes/cody/tags/jtc-for-upstream-pull-request:
block/ssh: Avoid segfault if inet_connect doesn't set errno.
sheepdog: serialize requests to overwrapping area
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let net_rx_packet() (which checks the same conditions) drops the packet
if the device is not ready. Drop net_xen_info.can_receive and update the
return value for the buffer full case.
We rely on the qemu_flush_queued_packets() in net_event() to wake up
the peer when the buffer becomes available again.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-id: 1438077176-378-1-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The network mcf_fec driver emulated receive side method is not dealing
with network queue flow control properly.
Modify the receive side to check if we have enough space in the
descriptors to store the current packet. If not we process none of it
and return 0. When the guest frees up some buffers through its descriptors
we signal the qemu net layer to send more packets.
[Fixed coding style: 4-space indent and curly braces on if statement.
--Stefan]
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Message-id: 1438045374-10358-1-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Replace memory_region_init_rom_device() with memory_region_init_ram() and
memory_region_set_readonly().
This fixes a guest-triggerable QEMU crash when guest tries to write to PROM.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
[leon.alrae@imgtec.com: shorten subject length]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Ethernet requires that messages are at least 64 bytes on the wire. This
limitation does not exist on emulation (no wire message), so remove the
check. Netcard is now able to receive small network packets.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Netcard needs an address space to write data to, which can't be specified
on command line.
This fixes a crash when user starts QEMU with "-device dp8393x"
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Block layer patches for 2.4.0-rc3
# gpg: Signature made Mon Jul 27 16:19:17 2015 BST using RSA key ID C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
* remotes/kevin/tags/for-upstream:
block: qemu-iotests - add check for multiplication overflow in vpc
block: vpc - prevent overflow if max_table_entries >= 0x40000000
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Correct computation of vector offsets for EXCP_EXT_INTERRUPT.
For instance, if Cause.IV is 0 the vector offset should be 0x180.
Simplify the finding vector number logic for the Vectored Interrupts.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com: cosmetic changes]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
On some (but not all) systems:
$ qemu-img create -f qcow2 overlay -b ssh://xen/
Segmentation fault
It turns out this happens when inet_connect returns -1 in the
following code, but errno == 0.
s->sock = inet_connect(s->hostport, errp);
if (s->sock < 0) {
ret = -errno;
goto err;
}
In the test case above, no host called "xen" exists, so getaddrinfo fails.
On Fedora 22, getaddrinfo happens to set errno = ENOENT (although it
is *not* documented to do that), so it doesn't segfault.
On RHEL 7, errno is not set by the failing getaddrinfo, so ret =
-errno = 0, so the caller doesn't know there was an error and
continues with a half-initialized BDRVSSHState struct, and everything
goes south from there, eventually resulting in a segfault.
Fix this by setting ret to -EIO (same as block/nbd.c and
block/sheepdog.c). The real error is saved in the Error** errp
struct, so it is printed correctly:
$ ./qemu-img create -f qcow2 overlay -b ssh://xen/
qemu-img: overlay: address resolution failed for xen:22: No address associated with hostname
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Reported-by: Jun Li
BZ: https://bugzilla.redhat.com/show_bug.cgi?id=1147343
Signed-off-by: Jeff Cody <jcody@redhat.com>
Current sheepdog driver only serializes create requests in oid
unit. This mechanism isn't enough for handling requests to
overwrapping area spanning multiple oids, so it can result bugs like
below:
https://bugs.launchpad.net/sheepdog-project/+bug/1456421
This patch adds a new serialization mechanism for the problem. The
difference from the old one is:
1. serialize entire aiocb if their targetting areas overwrap
2. serialize all requests (read, write, and discard), not only creates
This patch also removes the old mechanism because the new one can be
an alternative.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Teruaki Ishizaki <ishizaki.teruaki@lab.ntt.co.jp>
Cc: Vasiliy Tolstov <v.tolstov@selfip.ru>
Signed-off-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Tested-by: Vasiliy Tolstov <v.tolstov@selfip.ru>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Very often the owner of the aliased region is the same as the owner of the alias
region itself. When this happens, the reference count can never go back to 0 and
the owner is leaked. This is for example breaking hot-unplug of virtio-pci
devices (the device cannot be plugged back again with the same id).
Another common use for alias is to transform the system I/O address space
into an MMIO regions; in this case the aliased region never dies, so there
is no problem. Otherwise the owner is always the same for aliasing
and aliased region.
I checked all calls to memory_region_init_alias introduced after commit
dfde4e6 (memory: add ref/unref calls, 2013-05-06) and they do not need the
reference in order to keep the owner of the aliased region alive.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes a QEMU SEGFAULT when a write operation is performed on
the memory region of the PCI BAR 3 (base address space).
When a writeb(0xe0000000) is performed the .write function is invoked to
handle the write access, however, since the .write is not initialised,
the call to 0, causes QEMU to SEGFAULT.
Signed-off-by: Salva Peiró <speirofr@gmail.com>
Acked-by: Hannes Reinecke <hare@suse.com>
Message-Id: <1437987112-24744-1-git-send-email-speirofr@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
gdb expects that the thread ID for c and g-class operations is set to
the CPU we provide when reporting VM stop conditions. If the stub is
still tuned to a different CPU, the wrong information is delivered to
the gdb frontend.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The auto increment bit of the timer control register was wrongly
defined.
See Cortex-A9 MPcore Technical Reference Manual, Section 4.4.2.
Signed-off-by: Johannes Schlatow <schlatow@ida.ing.tu-bs.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
As of d98bc0b65 there are two files that are automatically generated:
ui/shader/texture-blit-frag.h and /ui/shader/texture-blit-vert.h. None
of them is wanted to be tracked by git. Put them into the ignore file
then.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
We want to have uniform build messages, so fix some messages
which did not follow the standard pattern.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add documentation comments for various utility string functions
which we have implemented in util/cutils.c:
pstrcpy()
strpadcpy()
pstrcat()
strstart()
stristart()
qemu_strnlen()
qemu_strsep()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fix buglets for 2.4
# gpg: Signature made Mon Jul 27 15:26:48 2015 BST using RSA key ID 4DD0279B
# gpg: Good signature from "Richard Henderson <rth7680@gmail.com>"
# gpg: aka "Richard Henderson <rth@redhat.com>"
# gpg: aka "Richard Henderson <rth@twiddle.net>"
* remotes/rth/tags/pull-tcg-20150727:
tcg: mark temps as mem_coherent = 0 for mov with a constant
tcg: correctly mark dead inputs for mov with a constant
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
aio_notify can be optimized away, and in fact almost always will. However,
qemu_notify_event is used in places where this is incorrect---most notably,
when handling SIGTERM. When aio_notify is optimized away, it is possible that
QEMU enters a blocking ppoll immediately afterwards and stays there, without
reaching main_loop_should_exit().
Fix this by using a bottom half. The bottom half can be optimized too, but
scheduling it is enough for the ppoll not to block. The hang is thus avoided.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1437738175-23624-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This checks that VPC is able to successfully fail (without segfault)
on an image file with a max_table_entries that exceeds 0x40000000.
This table entry is within the valid range for VPC (although too large
for this sample image).
Cc: qemu-stable@nongnu.org
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When we allocate the pagetable based on max_table_entries, we multiply
the max table entry value by 4 to accomodate a table of 32-bit integers.
However, max_table_entries is a uint32_t, and the VPC driver accepts
ranges for that entry over 0x40000000. So during this allocation:
s->pagetable = qemu_try_blockalign(bs->file, s->max_table_entries * 4);
The size arg overflows, allocating significantly less memory than
expected.
Since qemu_try_blockalign() size argument is size_t, cast the
multiplication correctly to prevent overflow.
The value of "max_table_entries * 4" is used elsewhere in the code as
well, so store the correct value for use in all those cases.
We also check the Max Tables Entries value, to make sure that it is <
SIZE_MAX / 4, so we know the pagetable size will fit in size_t.
Cc: qemu-stable@nongnu.org
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Unfortunately Ubuntu's pkg-config information for gnutls is broken
for the static linking case, and outputs --libs options which the
compiler does not recognize. Work around this problem by testing
that the --cflags/--libs output will at least allow compilation
before enabling gnutls support.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1437758888-22486-1-git-send-email-peter.maydell@linaro.org
Chapter 6.3 of spec said
"
Transitional devices MUST offer, and if offered by the device
transitional drivers MUST accept the following:
VIRTIO_F_ANY_LAYOUT (27)
"
So this patch only clear VIRTIO_F_LAYOUT for legacy device.
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
SCSI passthrough was no longer supported in virtio 1.0, so this patch
fail the get_features() when both 1.0 and scsi is set. And also only
advertise VIRTIO_BLK_F_SCSI for legacy virtio-blk device.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Each memory_region_add_subregion must be paired with
memory_region_del_subregion.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
When tcg_reg_alloc_mov propagate a constant, we failed to correctly mark
a temp as dead if the liveness analysis hints so. This fixes the
following assert when configure with --enable-debug-tcg:
qemu-x86_64: tcg/tcg.c:1827: tcg_reg_alloc_bb_end: Assertion `ts->val_type == TEMP_VAL_DEAD' failed.
Cc: Richard Henderson <rth@twiddle.net>
Reported-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-Id: <1437994568-7825-2-git-send-email-aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Pull request
Here are NIC fixes from Fam Zheng that prevent rx hangs (caused by NIC models
where .can_receive() stops rx but qemu_flush_queued_packets() isn't called).
# gpg: Signature made Mon Jul 27 14:51:48 2015 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/net-pull-request:
axienet: Flush queued packets when rx is done
dp8393x: Flush packets when link comes up
stellaris_enet: Flush queued packets when read done
mipsnet: Flush queued packets when receiving is enabled
milkymist-minimac2: Flush queued packets when link comes up
mcf_fec: Drop mcf_fec_can_receive
etsec: Flush queue when rx buffer is consumed
etsec: Move etsec_can_receive into etsec_receive
usbnet: Drop usbnet_can_receive
eepro100: Drop nic_can_receive
pcnet: Drop pcnet_can_receive
xgmac: Drop packets with eth_can_rx is false.
hw/net: fix mcf_fec driver receiver
hw/net: add simple phy support to mcf_fec driver
hw/net: add ANLPAR bit definitions to generic mii
hw/net: create common collection of MII definitions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
eth_can_rx checks s->rxsize and returns false if it is non-zero. Because
of the .can_receive semantics change, this will make the incoming queue
disabled by peer, until it is explicitly flushed. So we should flush it
when s->rxsize is becoming zero.
Squash eth_can_rx semantics into etx_rx and drop .can_receive()
callback, also add flush when rx buffer becomes available again after a
packet gets queued.
The other conditions, "!axienet_rx_resetting(s) &&
axienet_rx_enabled(s)" are OK because enet_write already calls
qemu_flush_queued_packets when the register bits are changed.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1436955553-22791-13-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
.can_receive callback changes semantics that once return 0, backend will
try sending again until explicitly flushed, change the device to meet
that.
dp8393x_can_receive checks SONIC_CR_RXEN bit in SONIC_CR register and
SONIC_ISR_RBE bit in SONIC_ISR register, try flushing the queue when
either bit is being updated.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-12-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
If s->np reaches 31, the queue will be disabled by peer when it sees
stellaris_enet_can_receive() returns false, until we explicitly flushes
it which notifies the peer. Do this when guest is done reading all
existing data.
Move the semantics to stellaris_enet_receive, by returning 0 when the
buffer is full, so that new packets will be queued. In
stellaris_enet_read, flush and restart the queue when guest has done
reading.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-11-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop .can_receive and move the semantics into minimac2_rx, by returning
0.
That is once minimac2_rx returns 0, incoming packets will be queued
until the queue is explicitly flushed. We do this when s->regs[R_STATE0]
or s->regs[R_STATE1] is changed in minimac2_write.
Also drop the unused trace point.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1436955553-22791-9-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The semantics of .can_receive requires us to flush the queue explicitly
when s->rx_enabled becomes true after it returns 0, but the packet being
queued is not meaningful since the guest hasn't activated the card.
Let's just drop the packet in this case.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-8-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
usbnet_receive already drops packet if rndis_state is not
RNDIS_DATA_INITIALIZED, and queues packet if in buffer is not available.
The only difference is s->dev.config but that is similar to rndis_state.
Drop usbnet_can_receive and move these checks to usbnet_receive, so that
we don't need to explicitly flush the queue when s->dev.config changes
value.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-5-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
nic_receive already checks the conditions and drop packets if false.
Due to the new semantics since 6e99c63 ("net/socket: Drop
net_socket_can_send"), having .can_receive returning 0 requires us to
explicitly flush the queued packets when the conditions are becoming
true, but queuing the packets when guest driver is not ready doesn't
make much sense.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-4-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
pcnet_receive already checks the conditions and drop packets if false.
Due to the new semantics since 6e99c63 ("net/socket: Drop
net_socket_can_send"), having .can_receive returning 0 requires us to
explicitly flush the queued packets when the conditions are becoming
true, but queuing the packets when guest driver is not ready doesn't
make much sense.
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Message-id: 1436955553-22791-3-git-send-email-famz@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The network mcf_fec driver emulated receive side method is returning a
result of 0 causing the network layer to disable receive for this emulated
device. This results in the guest only ever receiving one packet.
Fix the recieve side processing to return the number of bytes that we
passed back through to the guest.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-5-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The Linux fec driver needs at least basic phy support to probe and work.
The current qemu mcf_fec emulation has no support for the reading or
writing of the MDIO lines to access an attached phy.
This code adds a very simple set of register results for a fixed phy
setup - very similar to that used on an m5208evb board. This is enough
to probe and identify an emulated attached phy.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-4-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a base set of bit definitions for the standard MII phy "Auto-Negotiation
Link Partner Ability Register" (ANLPAR).
The original definitions moved into mii.h from the allwinner_emac driver
did not define these.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-3-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Create a common set of definitions of address and register values for
ethernet MII phys. A few of the current ethernet drivers have at least
a partial set of these definitions. Others just use hard coded raw
constant numbers.
This initial set is copied directly from the allwinner_emac code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435296436-12152-2-git-send-email-gerg@uclinux.org
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
# gpg: Signature made Mon Jul 27 13:01:10 2015 BST using RSA key ID AAFC390E
# gpg: Good signature from "John Snow (John Huston) <jsnow@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: FAEB 9711 A12C F475 812F 18F2 88A9 064D 1835 61EB
# Subkey fingerprint: F9B7 ABDB BCAC DF95 BE76 CBD0 7DEF 8106 AAFC 390E
* remotes/jnsnow/tags/cve-2015-5154-pull-request:
ide: Clear DRQ after handling all expected accesses
ide/atapi: Fix START STOP UNIT command completion
ide: Check array bounds before writing to io_buffer (CVE-2015-5154)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current unit test only verifies the encryption API,
resulting in us missing a recently introduced bug in the
decryption API from commit d3462e3. It was fortunately
later discovered & fixed by commit bd09594, thanks to the
QEMU I/O tests for qcow2 encryption, but we should really
detect this directly in the crypto unit tests. Also remove
an accidental debug message and simplify some asserts.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1437468902-23230-1-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
virtio pci allows any device to have a modern interface,
this in turn requires ANY_LAYOUT support.
Fix up ANY_LAYOUT for virtio-9p.
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Don't assume a specific layout for control messages.
Required by virtio 1.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
NOTIFY_ON_EMPTY, ANY_LAYOUT and BAD are only valid on the legacy
interface.
Hide them from modern guests.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is additional hardening against an end_transfer_func that fails to
clear the DRQ status bit. The bit must be unset as soon as the PIO
transfer has completed, so it's better to do this in a central place
instead of duplicating the code in all commands (and forgetting it in
some).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
The command must be completed on all code paths. START STOP UNIT with
pwrcnd set should succeed without doing anything.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
If the end_transfer_func of a command is called because enough data has
been read or written for the current PIO transfer, and it fails to
correctly call the command completion functions, the DRQ bit in the
status register and s->end_transfer_func may remain set. This allows the
guest to access further bytes in s->io_buffer beyond s->data_end, and
eventually overflowing the io_buffer.
One case where this currently happens is emulation of the ATAPI command
START STOP UNIT.
This patch fixes the problem by adding explicit array bounds checks
before accessing the buffer instead of relying on end_transfer_func to
function correctly.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
* qemu-char fixes
* SCSI fixes (including CVE-2015-5158)
* RCU fixes
* Framebuffer logic to set DIRTY_MEMORY_VGA
* Fix compiler warning for --disable-vnc
* qemu-doc fixes
* x86 TCG pasto fix
# gpg: Signature made Fri Jul 24 12:57:52 2015 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
target-i386/FPU: a misprint in helper_fistll_ST0
qemu-doc: fix typos
framebuffer: set DIRTY_MEMORY_VGA on RAM that is used for the framebuffer
memory: count number of active VGA logging clients
vl: Fix compiler warning for builds without VNC
scsi: Handle no media case for scsi_get_configuration
rcu: actually register threads that have RCU read-side critical sections
scsi: fix buffer overflow in scsi_req_parse_cdb (CVE-2015-5158)
vnc: fix memory leak
qemu-char: Fix missed data on unix socket
qemu-char: handle EINTR for TCP character devices
exec.c: Use atomic_rcu_read() to access dispatch in memory_region_section_get_iotlb()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MemoryRegionSection contains enough information to access the
RAM region underlying the framebuffer, and can be cached inside the
display device.
By doing this, the new framebuffer_update_memory_section function can
enable dirty memory logging on the relevant RAM region. The function
must be called whenever the stride or base of the framebuffer changes;
a simple way to cover these cases is to call it on every full frame
invalidation, which is a rare case.
framebuffer_update_display now works entirely on a MemoryRegionSection,
without going through cpu_physical_memory_map/unmap.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For a board that has multiple framebuffer devices, both of them
might want to use DIRTY_MEMORY_VGA on the same memory region.
The lack of reference counting in memory_region_set_log makes
this very awkward to implement.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, scsi_get_configuration always returns a current
profile (DVD or CD), even when there is actually no media present.
By comparison, ide/atapi uses a default profile of 0 (MMC_PROFILE_NONE)
for this case and checks for tray_open, so let's do the same for scsi.
This fixes a problem I'm seeing with Fedora 22 guests where systemd
cdrom_id fails to unmount after a QEMU-initiated eject against a
scsi cdrom device because it believes the media is still present
(but unreadable).
Signed-off-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Message-Id: <1436986352-10695-1-git-send-email-mjrosato@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is a guest-triggerable buffer overflow present in QEMU 2.2.0
and newer. scsi_cdb_length returns -1 as an error value, but the
caller does not check it.
Luckily, the massive overflow means that QEMU will just SIGSEGV,
making the impact much smaller.
Reported-by: Zhu Donghai (朱东海) <donghai.zdh@alibaba-inc.com>
Fixes: 1894df0281
Reviewed-by: Fam Zheng <famz@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Similar to the same fix for user-mode, except this instance
occurs on the softmmu path. Again, the tlb addend must be
the base register, while the guest address is the index.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
NUMA queue, 2015-07-22
# gpg: Signature made Wed Jul 22 19:11:04 2015 BST using RSA key ID 984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/numa-pull-request:
hostmem: Fix qemu_opt_get_bool() crash in host_memory_backend_init()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 812c1057 introduced HUP detection on unix and tcp sockets prior
to a read in tcp_chr_read. This unfortunately broke CloudStack 4.2
which relied on the old behaviour where data on a socket was readable
even if a HUP was present.
A working solution is to properly check the return values from recv,
handling a closed socket once there is no more data to read.
Also enable polling for G_IO_NVAL to ensure the callback is called
for all possible events as these should now be possible to handle
with the improved error detection.
Signed-off-by: Nils Carlson <pyssling@ludd.ltu.se>
Message-Id: <1437338396-22336-1-git-send-email-pyssling@ludd.ltu.se>
[Do not handle EINTR; use socket_error(). - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When accessing the dispatch pointer in an AddressSpace within an RCU
critical section we should always use atomic_rcu_read(). Fix an
access within memory_region_section_get_iotlb() which was incorrectly
doing a direct pointer access.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1437391637-31576-1-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
bootindex was incorrectly changed to a device Property during the
platform code split, resulting in it no longer working. Remove it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org # v2.3+
The RTL8168 quirk correctly describes using bit 31 as a signal to
mark a latch/completion, but the code mistakenly uses bit 28. This
causes the Realtek driver to spin on this register for quite a while,
20k cycles on Windows 7 v7.092 driver. Then it gets frustrated and
tries to set the bit itself and spins for another 20k cycles. For
some this still results in a working driver, for others not. About
the only thing the code really does in its current form is protect
the guest from sneaking in writes to the real hardware MSI-X table.
The fix is obviously to use bit 31 as we document that we should.
The other problem doesn't seem to affect current drivers as nobody
seems to use these window registers for writes to the MSI-X table, but
we need to use the stored data when a write is triggered, not the
value of the current write, which only provides the offset.
Note that only the Windows drivers from Realtek seem to use these
registers, the Microsoft drivers provided with Windows 8.1 do not
access them, nor do Linux in-kernel drivers.
Link: https://bugs.launchpad.net/qemu/+bug/1384892
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: qemu-stable@nongnu.org # v2.1+
This fixes the following crash, introduced by commit
49d2e648e8:
$ gdb --args qemu-system-x86_64 -machine pc,mem-merge=off -object memory-backend-ram,id=ram-node0,size=1024
[...]
Program received signal SIGABRT, Aborted.
(gdb) bt
#0 0x00007ffff253b8c7 in raise () at /lib64/libc.so.6
#1 0x00007ffff253d52a in abort () at /lib64/libc.so.6
#2 0x00007ffff253446d in __assert_fail_base () at /lib64/libc.so.6
#3 0x00007ffff2534522 in () at /lib64/libc.so.6
#4 0x00005555558bb80a in qemu_opt_get_bool_helper (opts=0x55555621b650, name=name@entry=0x5555558ec922 "mem-merge", defval=defval@entry=true, del=del@entry=false) at qemu/util/qemu-option.c:388
#5 0x00005555558bbb5a in qemu_opt_get_bool (opts=<optimized out>, name=name@entry=0x5555558ec922 "mem-merge", defval=defval@entry=true) at qemu/util/qemu-option.c:398
#6 0x0000555555720a24 in host_memory_backend_init (obj=0x5555562ac970) at qemu/backends/hostmem.c:226
Instead of using qemu_opt_get_bool(), that didn't work with
qemu_machine_opts for a long time, we can use the corresponding
MachineState fields.
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
2015-07-22 15:09:25 -03:00
186 changed files with 2397 additions and 1062 deletions
Loaded 100 of 186 files, more files were not shown because too many files have changed in this diff.
Show more
Reference in new issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.