In the current mdev_reg_read() implementation, it consistently returns
that the Media Status is Ready (01b). This was fine until commit
25a52959f9 ("hw/cxl: Add support for device sanitation") because the
media was presumed to be ready.
However, as per the CXL 3.0 spec "8.2.9.8.5.1 Sanitize (Opcode 4400h)",
during sanitation, the Media State should be set to Disabled (11b). The
mentioned commit correctly sets it to Disabled, but mdev_reg_read()
still returns Media Status as Ready.
To address this, update mdev_reg_read() to read register values instead
of returning dummy values.
Note that __toggle_media() managed to not only write something
that no one read, it did it to the wrong register storage and
so changed the reported mailbox size which was definitely not
the intent. That gets fixed as a side effect of allocating
separate state storage for this register.
Fixes: commit 25a52959f9 ("hw/cxl: Add support for device sanitation")
Signed-off-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Message-Id: <20240126120132.24248-7-Jonathan.Cameron@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
(cherry picked from commit f7509f462c788a347521f90f19d623908c4fbcc5)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
During drain, we do not care about virtqueue notifications, which is why
we remove the handlers on it. When removing those handlers, whether vq
notifications are enabled or not depends on whether we were in polling
mode or not; if not, they are enabled (by default); if so, they have
been disabled by the io_poll_start callback.
Because we do not care about those notifications after removing the
handlers, this is fine. However, we have to explicitly ensure they are
enabled when re-attaching the handlers, so we will resume receiving
notifications. We do this in virtio_queue_aio_attach_host_notifier*().
If such a function is called while we are in a polling section,
attaching the notifiers will then invoke the io_poll_start callback,
re-disabling notifications.
Because we will always miss virtqueue updates in the drained section, we
also need to poll the virtqueue once after attaching the notifiers.
Buglink: https://issues.redhat.com/browse/RHEL-3934
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202153158.788922-3-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
(cherry picked from commit 5bdbaebcce18fe6a627cafad2043ec08f3de5744)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
ISM devices are sensitive to manipulation of the IOMMU, so the ISM device
needs to be reset before the vfio-pci device is reset (triggering a full
UNMAP). In order to ensure this occurs, trigger ISM device resets from
subsystem_reset before triggering the PCI bus reset (which will also
trigger vfio-pci reset). This only needs to be done for ISM devices
which were enabled for use by the guest.
Further, ensure that AIF is disabled as part of the reset event.
Fixes: ef1535901a ("s390x: do a subsystem reset before the unprotect on reboot")
Fixes: 03451953c7 ("s390x/pci: reset ISM passthrough devices on shutdown and system reset")
Reported-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-ID: <20240118185151.265329-4-mjrosato@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 68c691ca99a2538d6a53a70ce8a9ce06ee307ff1)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use a flag to keep track of whether AIF is currently enabled. This can be
used to avoid enabling/disabling AIF multiple times as well as to determine
whether or not it should be disabled during reset processing.
Fixes: d0bc7091c2 ("s390x/pci: enable adapter event notification for interpreted devices")
Reported-by: Cédric Le Goater <clg@redhat.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Message-ID: <20240118185151.265329-2-mjrosato@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
(cherry picked from commit 07b2c8e034d80ff92e202405c494d2ff80fcf848)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
j is used while loading an ELF file to byteswap segments'
data. If data is larger than 2GB an overflow may happen.
So j should be elf_word.
This commit fixes a minor bug: it's unlikely anybody is trying to
load ELF files with 2GB+ segments for wrong-endianness targets,
but if they did, it wouldn't work correctly.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Cc: qemu-stable@nongnu.org
Fixes: 7ef295ea5b ("loader: Add data swap option to load-elf")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
(cherry picked from commit 410c2a4d75f52f6a2fe978eda5a9b6f854afe5ea)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
GUEST_VIRTIO_MMIO_* was added in Xen 4.17, so only define them
for CONFIG_XEN_CTRL_INTERFACE_VERSIONs up to 4.16.
Reported-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
getloadavg is supported on Linux, BSDs, Solaris.
Following man page:
RETURN VALUE
If the load average was unobtainable, -1 is returned; otherwise,
the number of samples actually retrieved is returned.
accordingly, make stub for systems which don't support this function return -1
for consistency.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The vhost-user-blk export implement AioContext switches in its drain
implementation. This means that on drain_begin, it detaches the server
from its AioContext and on drain_end, attaches it again and schedules
the server->co_trip coroutine in the updated AioContext.
However, nothing guarantees that server->co_trip is even safe to be
scheduled. Not only is it unclear that the coroutine is actually in a
state where it can be reentered externally without causing problems, but
with two consecutive drains, it is possible that the scheduled coroutine
didn't have a chance yet to run and trying to schedule an already
scheduled coroutine a second time crashes with an assertion failure.
Following the model of NBD, this commit makes the vhost-user-blk export
shut down server->co_trip during drain so that resuming the export means
creating and scheduling a new coroutine, which is always safe.
There is one exception: If the drain call didn't poll (for example, this
happens in the context of bdrv_graph_wrlock()), then the coroutine
didn't have a chance to shut down. However, in this case the AioContext
can't have changed; changing the AioContext always involves a polling
drain. So in this case we can simply assert that the AioContext is
unchanged and just leave the coroutine running or wake it up if it has
yielded to wait for the AioContext to be attached again.
Fixes: e1054cd4aa
Fixes: https://issues.redhat.com/browse/RHEL-1708
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231127115755.22846-1-kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The VIA integrated south bridge chips combine several functions and
allow routing their interrupts to any of the ISA IRQs also allowing
multiple sources to share the same ISA IRQ. E.g. pegasos2 firmware
configures everything to use IRQ 9 but amigaone routes them to
separate ISA IRQs so the current simplified routing does not work.
Bring back via_isa_set_irq() and change it to take the component that
wants to change an IRQ and keep track of interrupt status of each
source separately and do the mapping to ISA IRQ within the ISA bridge.
This may not handle cases when an ISA IRQ is controlled by devices
directly, not going through via_isa_set_irq() such as serial, parallel
or keyboard but these IRQs being conventionally fixed are not likely
to be change by guests or share with other devices so this does not
cause a problem in practice.
This reverts commit 4e5a20b6da.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <1c3902d4166234bef0a476026441eaac3dd6cda5.1701035944.git.balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The spips, qspips, and zynqmp-qspips share the same realize function
(xilinx_spips_realize) and initialize their io memory region with different
mmio_ops passed through the class. The size of the memory region is set to
the largest area (0x200 bytes for zynqmp-qspips) thus it is possible to write
out of s->regs[addr] in xilinx_spips_write for spips and qspips.
This fixes that wrong behavior.
Reviewed-by: Luc Michel <luc.michel@amd.com>
Signed-off-by: Frederic Konrad <fkonrad@amd.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@amd.com>
Message-id: 20231124143505.1493184-2-fkonrad@amd.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function reads the value of the PCI_CLASS_PROG register for PCI IDE
controllers and configures the PCI BARs and/or IDE ioports accordingly.
In the case where we switch to legacy mode, the PCI BARs are set to return zero
(as suggested in the "PCI IDE Controller" specification), the legacy IDE ioports
are enabled, and the PCI interrupt pin cleared to indicate legacy IRQ routing.
Conversely when we switch to native mode, the legacy IDE ioports are disabled
and the PCI interrupt pin set to indicate native IRQ routing. The contents of
the PCI BARs are unspecified, but this is not an issue since if a PCI IDE
controller has been switched to native mode then its BARs will need to be
programmed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20231116103355.588580-3-mark.cave-ayland@ilande.co.uk>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_graph_wrunlock() calls aio_poll(), which may run callbacks that
have a nested event loop. Nested event loops can depend on other
iothreads making progress, so in order to allow them to make progress it
must not hold the AioContext lock of another thread while calling
aio_poll().
This introduces a @bs parameter to bdrv_graph_wrunlock() whose
AioContext is temporarily dropped (which matches bdrv_graph_wrlock()),
and a bdrv_graph_wrunlock_ctx() that can be used if the BlockDriverState
doesn't necessarily exist any more when unlocking.
This also requires a change to bdrv_schedule_unref(), which was relying
on the incorrectly taken lock. It needs to take the lock itself now.
While this is a separate bug, it can't be fixed a separate patch because
otherwise the intermediate state would either deadlock or try to release
a lock that we don't even hold.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231115172012.112727-3-kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
[kwolf: Fixed up bdrv_schedule_unref()]
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
target-arm queue:
* enable FEAT_RNG on Neoverse-N2
* hw/intc/arm_gicv3: ICC_PMR_EL1 high bits should be RAZ
* Fix SME FMOPA (16-bit), BFMOPA
* hw/core/machine: Constify MachineClass::valid_cpu_types[]
* stm32f* machines: Report error when user asks for wrong CPU type
* hw/arm/fsl-imx: Do not ignore Error argument
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmVchLYZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3kHMD/47tKxzrsXc6+V9esRQGi2H
# 1hAgLBwglEdxLXokF+Di41sh/fvK7wYVXO/hiWlq+9h3kG3D/u1N5r1TdMPMUb9j
# 4Sg3rOejn7nzkxVZ6MZ/K/1j84C9bfrt4sboVHZVRvWuvbiyuTuivEr4IqLYO4x3
# AIwhFMQ5gbNrmClZh/DBxj0keO13cp63Fg2JSSICdi+1Dw9rRXTyhJloMu1omeqc
# k/BXzjSeNXpLSMyGWBR3uaPcJBaGC1xnz3Z1V7fUY1EYD2Cu1oo5lEZ9aNO5t30d
# XW/qVGLa3b1Cb7WuEO247RnU3N2oZotozjFtdj/8IQoYWspM9RHyipEimUlegVdO
# 3fpu8QGsN1ljNiwjdk0i6OwS7SGxcPtteFOaqEf/Yogj4EOKTn/Rx5TT4vJ5DhmI
# 2w/9J15JWDIE1paNwecuFWbxCOOzSsOtSxzuyLSZDU3GlNfJ4zoF6YboROLYfejy
# NXZABFhGd/0ykX7r0VY1GGYXUQ+akv6q+VDmVZCP9gMiRUiqmFPwMLMLlcuHb8G5
# 8UztN5SvOG2EYXj28Zx0BnGCNiGdI15rWMb0veqAtbnn3yEdltW3O475BAhZ0PB7
# OVpLWnXwmWURm/BGlwb1PH5s3kgWgzOebcBgcnCftwFQ8EedQAQDA5FmT+nK5SfV
# VoOf89PngTubU6B3BOfeBw==
# =thIa
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 21 Nov 2023 05:21:42 EST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20231121' of https://git.linaro.org/people/pmaydell/qemu-arm:
hw/arm/fsl-imx: Do not ignore Error argument
hw/arm/stm32f100: Report error when incorrect CPU is used
hw/arm/stm32f205: Report error when incorrect CPU is used
hw/arm/stm32f405: Report error when incorrect CPU is used
hw/core/machine: Constify MachineClass::valid_cpu_types[]
target/arm: Fix SME FMOPA (16-bit), BFMOPA
hw/intc/arm_gicv3: ICC_PMR_EL1 high bits should be RAZ
target/arm: enable FEAT_RNG on Neoverse-N2
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In the minimal pixman API stub that is used when the real pixman
dependency is missing a NULL dereference happens when
virtio-gpu-rutabaga allocates a pixman image with bits = NULL and
rowstride_bytes = zero. A buffer of rowstride_bytes * height is
allocated which is NULL. However, in that scenario pixman calculates a
new stride value based on given width, height and format size.
This commit adds a helper function that performs the same logic as
pixman.
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20231121093840.2121195-1-manos.pitsidianakis@linaro.org>
Recently MemReentrancyGuard was added to DeviceState to record that the
device is engaging in I/O. The network device backend needs to update it
when delivering a packet to a device.
This implementation follows what bottom half does, but it does not add
a tracepoint for the case that the network device backend started
delivering a packet to a device which is already engaging in I/O. This
is because such reentrancy frequently happens for
qemu_flush_queued_packets() and is insignificant.
Fixes: CVE-2023-3019
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Acked-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Recently MemReentrancyGuard was added to DeviceState to record that the
device is engaging in I/O. The network device backend needs to update it
when delivering a packet to a device.
In preparation for such a change, add MemReentrancyGuard * as a
parameter of qemu_new_nic().
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The 'stm32vldiscovery' machine ignores the CPU type requested by
the command line. This might confuse users, since the following
will create a machine with a Cortex-M3 CPU:
$ qemu-system-aarch64 -M stm32vldiscovery -cpu neoverse-n1
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-aarch64 -M stm32vldiscovery -cpu neoverse-n1
qemu-system-aarch64: Invalid CPU type: neoverse-n1-arm-cpu
The valid types are: cortex-m3-arm-cpu
Since the SoC family can only use Cortex-M3 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-5-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'netduino2' machine ignores the CPU type requested by the
command line. This might confuse users, since the following will
create a machine with a Cortex-M3 CPU:
$ qemu-system-arm -M netduino2 -cpu cortex-a9
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-arm -M netduino2 -cpu cortex-a9
qemu-system-arm: Invalid CPU type: cortex-a9-arm-cpu
The valid types are: cortex-m3-arm-cpu
Since the SoC family can only use Cortex-M3 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-4-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Both 'netduinoplus2' and 'olimex-stm32-h405' machines ignore the
CPU type requested by the command line. This might confuse users,
since the following will create a machine with a Cortex-M4 CPU:
$ qemu-system-aarch64 -M netduinoplus2 -cpu cortex-r5f
Set the MachineClass::valid_cpu_types field (introduced in commit
c9cf636d48 "machine: Add a valid_cpu_types property").
Remove the now unused MachineClass::default_cpu_type field.
We now get:
$ qemu-system-aarch64 -M netduinoplus2 -cpu cortex-r5f
qemu-system-aarch64: Invalid CPU type: cortex-r5f-arm-cpu
The valid types are: cortex-m4-arm-cpu
Since the SoC family can only use Cortex-M4 CPUs, hard-code the
CPU type name at the SoC level, removing the QOM property
entirely.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Message-id: 20231117071704.35040-3-philmd@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixes: 388d6b574e "hw/cxl: Use switch statements for read and write of cachemem registers"
Fixes: 3314efd276 "hw/cxl/mbox: Add Physical Switch Identify command."
Fixes: 004e3a93b8 "hw/cxl: Add tunneled command support to mailbox for switch cci."
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
When compiling QEMU with Clang 17 on a s390x, the compilation fails:
In file included from ../accel/tcg/cputlb.c:32:
In file included from /root/qemu/include/exec/helper-proto-common.h:10:
In file included from /root/qemu/include/qemu/atomic128.h:62:
/root/qemu/host/include/generic/host/atomic128-ldst.h:68:15: error:
__sync builtin operation MUST have natural alignment (consider using __
atomic). [-Werror,-Wsync-alignment]
68 | } while (!__sync_bool_compare_and_swap_16(ptr_align, old, new.i));
| ^
In file included from ../accel/tcg/cputlb.c:32:
In file included from /root/qemu/include/exec/helper-proto-common.h:10:
In file included from /root/qemu/include/qemu/atomic128.h:61:
/root/qemu/host/include/generic/host/atomic128-cas.h:36:11: error:
__sync builtin operation MUST have natural alignment (consider using __a
tomic). [-Werror,-Wsync-alignment]
36 | r.i = __sync_val_compare_and_swap_16(ptr_align, c.i, n.i);
| ^
2 errors generated.
It's arguably a bug in Clang since we already use __builtin_assume_aligned()
to tell the compiler that the pointer is properly aligned. But according to
https://github.com/llvm/llvm-project/issues/69146 it seems like the Clang
folks don't see an easy fix on their side and recommend to use a type
declared with __attribute__((aligned(16))) to work around this problem.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1934
Message-ID: <20231108085954.313071-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Until now, array properties are actually implemented with a hack that
uses multiple properties on the QOM level: a static "foo-len" property
and after it is set, dynamically created "foo[i]" properties.
In external interfaces (-device on the command line and device_add in
QMP), this interface was broken by commit f3558b1b ('qdev: Base object
creation on QDict rather than QemuOpts') because QDicts are unordered
and therefore it could happen that QEMU tried to set the indexed
properties before setting the length, which fails and effectively makes
array properties inaccessible. In particular, this affects the 'ports'
property of the 'rocker' device, which used to be configured like this:
-device rocker,len-ports=2,ports[0]=dev0,ports[1]=dev1
This patch reworks the external interface so that instead of using a
separate top-level property for the length and for each element, we use
a single true array property that accepts a list value. In the external
interfaces, this is naturally expressed as a JSON list and makes array
properties accessible again. The new syntax looks like this:
-device '{"driver":"rocker","ports":["dev0","dev1"]}'
Creating an array property on the command line without using JSON format
is currently not possible. This could be fixed by switching from
QemuOpts to a keyval parser, which however requires consideration of the
compatibility implications.
All internal users of devices with array properties go through
qdev_prop_set_array() at this point, so updating it takes care of all of
them.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1090
Fixes: f3558b1b76
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231109174240.72376-12-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Block layer patches
- Graph locking part 6 (bs->file/backing)
- ahci: trigger either error IRQ or regular IRQ, not both
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmVLvccRHGt3b2xmQHJl
# ZGhhdC5jb20ACgkQfwmycsiPL9ZkFg//awQoPiGnYzHpqcx2tGCM2AqBV+mFkbZr
# BKI5vp8FYfJtgMuHjC8jabL24NRMPpT+HbCzoxwjJU+nnnr85qr7R5iGwG6kfgX6
# HJlAXYXdY6e7l+FV44PBJ52vOoGCsh1GHg8HlKsHMaxSdXi9C1axHJ6rCAjnWXE0
# FQ4znCBVs/9HiKsvu4Wdm5muX2ShftFRM/toAwA+fLEOealX8WEXoRFJXI40bYbR
# OR7aJXWMDQrljlqdKk2FXvK337/tpofXmXf3NIE1R2pmY4x5Fg8bfChZn4UaaCdN
# n+0AhmE4ScI0rXuaXXYOvTO9vdTzXeBROG6tX03t9rrQfB6wPcGVeXRo/uusslAW
# sDH8NLz7uHFOooV02Fs8CKDdVrNNw5qjziclSGa0Po7vqOV1TKI8OTiNpsDLmdI5
# +DQvC6N+IU1pSOXImATSHkheGWggsegrsgN6PdrlzHEXJwWoAaRD0T06MRn74/pL
# gCegK2ez4RJYsci7C5b0gaqY/QBsMj8EUfEGVHvVyuVSoPRwiq4ehPqSQ+siA3xP
# KxYR0e4+QIfRmxqCzaJhiQ3DDGdt8UcO3yF0XcKXEqWwgFAGQKNeUG314jginvmA
# iaJzC0dHbiGcagAk7Ey8iyzfxQDWM6ixzJtGv7VLILepzCuu8vaJXy5qeEtTM/ZI
# EXoDGceNSvw=
# =ikBW
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 09 Nov 2023 00:56:39 HKT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* tag 'for-upstream' of https://repo.or.cz/qemu/kevin: (25 commits)
hw/ide/ahci: trigger either error IRQ or regular IRQ, not both
block: Protect bs->file with graph_lock
block: Take graph lock for most of .bdrv_open
vhdx: Take locks for accessing bs->file
qcow2: Take locks for accessing bs->file
block: Add missing GRAPH_RDLOCK annotations
block: Introduce bdrv_co_change_backing_file()
blkverify: Add locking for request_fn
block: Protect bs->backing with graph_lock
block: Mark bdrv_replace_node() GRAPH_WRLOCK
block: Mark bdrv_replace_node_common() GRAPH_WRLOCK
block: Inline bdrv_set_backing_noperm()
block: Mark bdrv_set_backing_hd_drained() GRAPH_WRLOCK
block: Mark bdrv_cow_child() and callers GRAPH_RDLOCK
block: Mark bdrv_filter_child() and callers GRAPH_RDLOCK
block: Mark bdrv_chain_contains() and callers GRAPH_RDLOCK
block: Mark bdrv_(un)freeze_backing_chain() and callers GRAPH_RDLOCK
block: Mark bdrv_skip_filters() and callers GRAPH_RDLOCK
block: Mark bdrv_skip_implicit_filters() and callers GRAPH_RDLOCK
block: Mark bdrv_filter_or_cow_bs() and callers GRAPH_RDLOCK
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Almost all functions that access bs->file already take the graph
lock now. Add locking to the remaining users and finally annotate the
struct field itself as protected by the graph lock.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231027155333.420094-25-kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This adds GRAPH_RDLOCK to some driver callbacks that are already called
with the graph lock held, and which will need the annotation because
they access bs->file, but don't have it yet.
This also covers a few callbacks that were not marked GRAPH_RDLOCK
before, but where updating BlockDriver is trivially possible.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231027155333.420094-21-kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_change_backing_file() is called both inside and outside coroutine
context. This makes it difficult for it to take the graph lock
internally. It also means that driver implementations need to be able to
run outside of coroutines, too. Switch it to the usual model with a
coroutine based implementation and a co_wrapper instead. The new
function is marked GRAPH_RDLOCK.
As the co_wrapper now runs the function in the AioContext of the node
(as it should always have done), this is not GLOBAL_STATE_CODE() any
more.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231027155333.420094-20-kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Almost all functions that access bs->backing already take the graph
lock now. Add locking to the remaining users and finally annotate the
struct field itself as protected by the graph lock.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231027155333.420094-18-kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Hyeonggon Yoo
Richard Henderson
Hanna Czenczek
Matthew Rosato
Anastasia Belova
Elen Avan
Stefan Hajnoczi
Paolo Bonzini
Michael S. Tsirkin
Kevin Wolf
BALATON Zoltan
Frederic Konrad
Philippe Mathieu-Daudé
Mark Cave-Ayland
Manos Pitsidianakis
Akihiko Odaki
Gavin Shan
Michael Tokarev
Janosch Frank
Thomas Huth
Greg Manning